SPEC: 25010

CSA TECK 90 CU 1000V NON-SHIELDED XLPE POWER CABLE

1000V, Non-Shielded, XLPE Insulation, FT4, -40°C, HL (Hazardous Locations), 90°C

Télécharger les spécifications de la catégorie

Application & Features

Southwire's Single Conductor 1kV Teck 90 is a CSA approved armoured cable for Industrial and Commercial applications. FT4, -40C, HL, AG14 and 90°C rated for use in harsh Canadian environments. Rated for installation in cable trays, duct banks, direct burial, troughs, hazardous locations, continuous rigid cable supports, and concrete encaseable. CSA AG14 Acid Gas compliance.

-40°C - CSA Cold Bend and Impact Temperature
-25°C - Min. Installation Temperature
90°C - Max. Continuous Operating Temperature
140°C for Emergency Overload Temperature

Spécifications

Pour plus d’informations, sélectionnez un ensemble de produits ci-dessous :

	Cond. Dimensions	Cond. Strands	Diameter Over Conductor (in) (cm)	Épaisseur de l’isolation (mils) (mm)	Inner Jacket Thickness (mils) (mm)	Diameter Over Armor (in) (cm)	Drain Wire	Épaisseur de la jaquette (mils) (mm)	Approx. OD (in) (cm)	Approx. Weight (lbs/1000') (kgs/km)	Max Pull Tension (lbs) (kg)	Min. Rayon de courbure (pouces) (centimètres)
More Options	4/0 AWG 4/0 AWG	19 19	0.512 1.30	80 2.03	55 1.40	1.221 3.10	13x14 13x14	45 1.14	1.311 3.33	1271 1891	1692 767.48	9.1 23.11
More Options	350 KCMIL 350 KCMIL	37 37	0.661 1.68	90 2.29	60 1.52	1.449 3.68	13x12 13x12	45 1.14	1.539 3.91	1935 2880	2800 1270.06	10.7 27.18
More Options	500 KCMIL 500 KCMIL	37 37	0.789 2.00	90 2.29	60 1.52	1.574 4.00	17x12 17x12	55 1.40	1.684 4.28	2579 3838	4000 1814.37	11.7 29.72
More Options	750 KCMIL 750 KCMIL	61 61	0.968 2.46	90 2.29	60 1.52	1.771 4.50	21x12 21x12	55 1.40	1.881 4.78	3572 5316	6000 2721.55	13.1 33.27

* Other conductor sizes and outer jacket colours are available upon request. (#s in brackets represent # of strands / conductor. Number of strands may vary as per CSA standard.)
** Non-Standard sizes are available upon request. Reel sizes are not guaranteed. The factory reserves the right to make changes as necessary to optimize manufacturing requirements.

	Cond. Dimensions	DC Resistance at 25C (ohms/1000') (ohms/km)	AC Resistance at 75C (ohms/1000') (ohms/km)	Inductive Reactance (ohms/1000') (ohms/km)
More Options	4/0 AWG 4/0 AWG	0.051 0.08	0.062 0.09	0.041 0.06
More Options	350 KCMIL 350 KCMIL	0.031 0.05	0.039 0.06	0.040 0.06
More Options	500 KCMIL 500 KCMIL	0.022 0.03	0.029 0.04	0.039 0.06
More Options	750 KCMIL 750 KCMIL	0.014 0.02	0.022 0.03	0.038 0.06

* Inductive impedance is based on non-ferrous conduit with one diameter spacing center-to-center.

Normes et références

ASTM B3 Soft or Annealed Copper Wire
Conducteurs en cuivre toronné à couche concentrique ASTM B8
CSA C22.2 No. 174 Cables in Hazardous Locations
CSA C22.2 No. 131 Type TECK 90 Cable
CSA C22.2 No. 2556 & No. 0.3 Wire and Cable Test Methods
CSA LTGG [-40°C] - as per C68.10 - for Cold Bend and Impact rating
CSA HL - for Hazardous Locations rating
CSA SUN RES - for Sunlight Resistant rating
CSA AG14 - Acid Gas Compliance
ICEA S-96-659 (NEMA WC 71) 2001-5000 V Câbles non-blindés
Test de résistance aux flammes sur chemin de câbles vertical IEEE 1202 FT4 (70 000 Btu/h)
FT1 Flame Test (1,706 BTU/Hr nominal - Vertical Wire Flame Test)

Construction

Conducteur : Class B stranded compressed copper in accordance with ASTM B3 and ASTM B8
Isolation : XLPE (Cross Linked Polyethylene), Minimum Average Thickness: 4/0 = 0.08 inches (2.03 mm), 250 kcmil to 1000 kcmil = 0.090 inches (2.3 mm), 90°C
Concentric Bonding Conductors: Class B, concentric bare copper wire serve
Liaison/attache : Polypropylene Separator
Inner Jacket: Black PVC, Minumum average thickness - 4/0 = 0.050" (1.27mm), 250 kcmil to 1000 kcmil = 0.060" (1.5 mm)
Armor: Aluminum Interlocked Armour (AIA)
Overall Jacket: Black PVC (optional colours available), Minimum Thickness: 4/0 to 400 kcmil = 0.050 inches (1.3 mm), 500 kcmil to 1000 kcmil = 0.060 inches (1.5 mm)

Ressources

Il n’existe aucune ressource téléchargeable pour ce produit.