Les câbles 15 kV de Southwire conviennent pour une utilisation en zones humides et sèches, conduits, gaines, passages, chemins, enfouissement direct, et où des propriétés électriques supérieures sont désirées. Ces câbles peuvent fonctionner en continu à une température de conducteur ne dépassant pas 105 °C pour un fonctionnement normal, 140 °C pour une surcharge d’urgence et 250 °C en des conditions de court-circuit. Rated at -35°C for cold bend when UL listed. Rated at -40°C for cold bend and cold impact and marked with "LTGG" when CSA listed or dual UL/CSA listed. Pour une utilisation dans les endroits dangereux de catégorie I et II, Division 2 conformément aux articles 501 et 502.Classé pour 454 kg./Pression latérale maximale FT.
| Cond. Dimensions | Cond. Strands | Diameter Over Conductor (in) (cm) | Diameter Over Insulation (in) (cm) | Épaisseur de l’isolation (mils) (mm) | Diameter Over Shield (in) (cm) | Ground Size | Diameter Over Armor (in) (cm) | Épaisseur de la jaquette (mils) (mm) | Approx. OD (in) (cm) | Approx. Weight (lbs/1000') (kgs/km) | Max Pull Tension (lbs) (kg) | Min. Rayon de courbure (pouces) (centimètres) | |
| More Options |
1/0 AWG 1/0 AWG
|
10 10
|
0.336 0.85
|
0.814 2.07
|
220 5.59
|
0.874 2.22
|
1x6 1x6
|
2.259 5.74
|
75 1.91
|
2.409 6.12
|
2335 3475
|
1900 861.82
|
16.8 42.67
|
| More Options |
2/0 AWG 2/0 AWG
|
12 12
|
0.376 0.96
|
0.854 2.17
|
220 5.59
|
0.914 2.32
|
1x4 1x4
|
2.345 5.96
|
80 2.03
|
2.511 6.38
|
2620 3899
|
2395 1086.35
|
17.5 44.45
|
| More Options |
4/0 AWG 4/0 AWG
|
18 18
|
0.474 1.20
|
0.953 2.42
|
220 5.59
|
1.013 2.57
|
1x4 1x4
|
2.559 6.50
|
80 2.03
|
2.725 6.92
|
3089 4597
|
3808 1727.28
|
19.0 48.26
|
| More Options |
250 KCMIL 250 KCMIL
|
22 22
|
0.520 1.32
|
1.006 2.56
|
220 5.59
|
1.066 2.71
|
1x3/0 1x3/0
|
2.674 6.79
|
80 2.03
|
2.840 7.21
|
3734 5557
|
4500 2041.16
|
19.8 50.29
|
| More Options |
500 KCMIL 500 KCMIL
|
34 34
|
0.735 1.87
|
1.244 3.16
|
220 5.59
|
1.304 3.31
|
1x1 1x1
|
3.188 8.10
|
90 2.29
|
3.376 8.58
|
5019 7469
|
9000 4082.33
|
23.6 59.94
|
* Strand count meets minimum number per ASTM
| Cond. Dimensions | DC Resistance at 25C (ohms/1000') (ohms/km) | AC Resistance at 75C (ohms/1000') (ohms/km) | Capacitive Reactance (ohms/1000') (ohms/km) | Inductive Reactance (ohms/1000') (ohms/km) | Zero Sequence Impedance (ohms/1000') (ohms/1000') | Positive Sequence Impedance (ohms/1000') (ohms/1000') | Shield Short Circuit Current 6 Cycles | Allowable Ampacity In Duct 90C | Allowable Ampacity In Duct 105C | Allowable Ampacity In Air 90C | Allowable Ampacity In Air 105C | |
| More Options |
1/0 AWG 1/0 AWG
|
0.168 0.25
|
0.211 0.31
|
0.046 0.07
|
0.044 0.07
|
0.584 + j0.394 0.584 + j0.394
|
0.211 + j0.043 0.211 + j0.043
|
2738 2738
|
150 150
|
165 165
|
170 170
|
185 185
|
| More Options |
2/0 AWG 2/0 AWG
|
0.133 0.20
|
0.167 0.25
|
0.042 0.06
|
0.043 0.06
|
0.538 + j0.377 0.538 + j0.377
|
0.167 + j0.041 0.167 + j0.041
|
2862 2862
|
170 170
|
185 185
|
190 190
|
215 215
|
| More Options |
4/0 AWG 4/0 AWG
|
0.084 0.13
|
0.105 0.16
|
0.036 0.05
|
0.040 0.06
|
0.469 + j0.339 0.469 + j0.339
|
0.105 + j0.038 0.105 + j0.038
|
3166 3166
|
220 220
|
240 240
|
255 255
|
285 285
|
| More Options |
250 KCMIL 250 KCMIL
|
0.071 0.11
|
0.090 0.13
|
0.034 0.05
|
0.039 0.06
|
0.45 + j0.321 0.45 + j0.321
|
0.09 + j0.037 0.09 + j0.037
|
3333 3333
|
245 245
|
265 265
|
280 280
|
315 315
|
| More Options |
500 KCMIL 500 KCMIL
|
0.035 0.05
|
0.046 0.07
|
0.026 0.04
|
0.035 0.05
|
0.386 + j0.26 0.386 + j0.26
|
0.046 + j0.033 0.046 + j0.033
|
3999 3999
|
355 355
|
385 385
|
425 425
|
475 475
|
* NEC ampacities are based on:
* For Duct: Table 310.60(C)(14) Detail 1.
* For Free Air: Table 310.60(C)(6).
* Inductive impedance is based on non-ferrous conduit with one diameter spacing center-to-center.
* Sequence Impedance values are based on Rho Earth Resistivity: 100 Ohm-Meter/1000ft.
* Capacitive Reactance is between Phase-to-Shield.
